Please visit our Online Store at
www.cvgshop.com to
order!
 |
“Tone-Lock” Locking STEEL Studs/Spacer Rings:
Pro Sustainer System, superior tailpiece locking solution.
Patent
Pending solid “No Gap” technology locks
tailpiece to studs for superior sustain, even when raised off the body.
Competitive products, which merely lock the tailpiece to an original style
stud, do not compare! Guaranteed to increase sustain or your money back!
Kit contains 2 Steel studs, in inch or metric thread, plus 3 pairs of
spacers (2.5, 4 and 5.5 mm). Nickel or Gold Plated Steel. INCH (Imperial) threads for all USA made Gibson
guitars. METRIC threads for most guitars made outside the USA.
|
 |
TP-’59 Vintage Spec Stop Tailpiece:
An
extremely
lightweight stop tailpiece, of
correct vintage style, weighing ¼ of the zinc tailpieces used on modern
guitars. They transfer vibration much differently, resulting in a woodier,
more vintage, tone - a direct replacement for your Gibson
and most other stop tailpieces – just remove the old, zinc, tone robbing tailpiece and replace it
with this superior solution. Available in various finishes
to suit all applications. |
 |
TITANIUM TP-’59 Stop
Tailpiece:
The ultimate tailpiece upgrade! Hand shaped in the traditional
way! An unbelievable increase in sustain and pick attack! Combine one of
these with one of our “Tone-Lock” kits and one of our titanium saddle
bridges and turn your guitar into a super
sustaining tone machine! |
 |
ABR-’59
“No Wire” Vintage Spec Bridge:
For Nashville Replacement and Imports w/4MM bridge posts
Perhaps the most
vintage correct replacement bridge available on the market today! No
rattle-causing retainer wire! Increased sustain and pick attack due to the
brass saddles being countersunk from a solid piece of brass – not cast! Flat top saddles provide tight, 100% mechanical contact
in the ABR frame. Available in various frame and saddle finishes, including
TITANIUM saddles (nickel plated frame only)! Saddles (natural, nickel and
gold plated) have starter notches dead center; titanium saddles not
pre-notched. Use with existing Nashville style posts/wheels, or our BSWKIT/NSWKIT steel studs and
thumbwheels.
NEW!!! Now with removable saddles!
|
 |
ABRH-’59
“No Wire” Vintage Spec Bridge:
For Gibson Historics and original ABR-1 (6-32) size bridge posts
Perhaps the most
vintage correct replacement bridge available on the market today! No
rattle-causing retainer wire! Increased sustain and pick attack due to the
brass saddles being countersunk from a solid piece of brass – not cast! Flat top saddles provide tight, 100% mechanical contact
in the ABR frame. Available in various frame and saddle finishes,
including TITANIUM saddles (nickel plated frame only)! Saddles (natural, nickel and gold plated) have
starter notches dead center; titanium saddles not pre-notched. Use with
existing ABR-1 studs and thumbwheels.
NEW!!!
Now with removable saddles!
|
 |
ABRL"Tone-Lock" Bridge:
Locking Bridge For Gibson Historics (ABR-1), Nashville Replacement & Imports
Same features as our standard "No Wire" bridges
PLUS
Pro Sustainer System patent pending technology locks bridge to studs
for superior sustain - guaranteed!!! The best locking bridge solution on the
market and the only one that actually increases sustain, using our exclusive
Tone-Lock technology. A simple set screw, as used on competitive products,
doesn't compare!
Available for both original Gibson ABR-1 bridge studs
(Inch thread) and Nashville/import 4MM equipped guitars (Metric
thread).
Saddles (natural,
nickel and gold plated) have starter notches dead center; titanium saddles
not pre-notched.
NOTE: Nashville equipped guitars require BSWKIT or NSWKIT
(see below) to use
locking ABRL!
Details... |
 |
"BSWKIT"
STEEL Vintage Style Bridge Studs/Thumbwheels:
The Faber BSWKIT will give your Nashville bridge
equipped guitar the "vintage" look, while, at the same time, enhancing your
tone with steel posts (8MM base/4MM post) that provide better body contact
and more mass than the original zinc inserts. Combined with one of our Faber
ABR-'59 bridges (not included), this is the HOT bridge setup for your
guitar! Comes with one pair STEEL studs, thumbwheels (gloss nickel, aged
nickel, gloss gold or aged gold) and two 4MM hex nuts for installation. Note: 8MM stud base
can screw directly into guitars with 8MM inserts, such as Epiphone, and no
drilling/tapping is necessary on such guitars.
View Installation Instructions
|
 |
"NSWKIT"
STEEL Bridge Studs/Thumbwheels for Nashville equipped guitars:
This is the solution for owners of Nashville
equipped guitars who want the "vintage" look without the need to drill and
tap the guitar body. Although not as sustain enhancing as our BSWKIT, the
NSWKIT with steel posts (5MM base/4MM stud), is a huge improvement over the
stock inserts and will easily allow you to the use our Tone-Lock Bridge
(metric). Comes with one pair STEEL studs with integrated thumbwheels (gloss
nickel, aged nickel, gloss gold or aged gold). |
 |
TPW-’59
Vintage Spec WRAPAROUND Tailpiece:
Non-compensated lightweight aluminum tailpiece, correct vintage ‘50s style.
A perfect replacement for your vintage piece, either to replace one that is
worn, or to use while you store your original tailpiece to preserve it. Aluminum, plated in gloss Nickel or Gold. |
 |
TPWC-’59
Vintage Spec COMPENSATED WRAPAROUND Tailpiece:
Lightweight aluminum compensated wraparound tailpiece based on a
historic correct ’59. Tired of playing only to the 7th fret? This
is the solution! Put one on your vintage guitar to get perfect intonation,
while storing and preserving your original. Allen screws on both sides,
comes with Allen wrench for adjustments. Nickel, Aged Nickel or gold plated.
NOTE:
Best for use on guitars with OFFSET inserts (i.e., '61 and earlier
Gibson and reissues with offset inserts)
|
PRICE LIST |
PRICE LIST
Click to view
Current Retail
Price List
|
U.S.A Distributor, CV Guitars, Allentown, PA 18104
Tel. (610) 217-4298
Web:
www.cvguitars.com
Online Store:
www.cvgshop.com
e-mail:
info@cvguitars.com
In Europe: Faber-Germany
Web: Order Form
e-mail:
info@tokaiguitar.de
In Australia: Ultra-Technologies, POBox 548,
Brookvale NSW 2100
Ph (02) 9938 4153 Mobile 0419 633 971
Web:
www.ultra-technologies.net
e-mail: info@ultra-technologies.net
|
